Willkommen, Gast
Benutzername: Passwort: Angemeldet bleiben:
  • Seite:
  • 1

THEMA:

Wingtypes 27 Mär 2023 12:47 #1

  • lazor96
  • lazor96s Avatar Autor
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 8
  • Dank erhalten: 2
Dear Jeti,

a lot of people ask for more Wingtypes in the basic configuration of a new model.
If you have for example a Biplane with 4 aileron servos or a 104" or larger 3D aerobatic plane with 2 or more servos per control surface you always have to choose "4 aileron 2 flaps" or "4 aileron 4 flaps".
This means you will have a function "flaps" in the function list that is not used.
Yes, you can just ignore it and not assign it in the servo assignment but....
On a large plane with a lot of functions it gets a bit confusing if there are functions that are not assigned.
It would be better for understanding if there were options for 4 ailerons with out flaps or even 6 ailerons.

In the past it was possible to choose "4 aileron 2 flaps" and then just remove the flaps out of the function list but since an update this is not possible anymore.
If you try to delete the "flaps" function it will automaticly create the function "flaps" again. There is no way to delete it at the moment.

Thank you very much.

Best regards
Lars
Folgende Benutzer bedankten sich: stoeptegel

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Wingtypes 27 Mär 2023 13:07 #2

  • PW
  • PWs Avatar
  • Offline
  • Moderator
  • Moderator
  • Beiträge: 9329
  • Dank erhalten: 3510
Hi,

why so complicated:

1.

we use F3A biplanes and the two servos on the left side are Aileron 1/Aileron1 and on the right side aileron 2/aileron 2.


2.

same for IMAC plane

having for example 6 aileron servos

ailerion 1/aileron1/aileron 1 on the left side and aileron 2/aileron2/aileron2 on the right side.


Very easy ...


Regards
PW
Rechtsbeistand u.a. bei "Modellflugproblemen"etc. : Rechtsanwälte Wessels & Partner, Tel.: 02362/27065

PW Modellbautechnik ( Jeti Kombiangebote, Beratung/Einstellservice etc.)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von PW.

Wingtypes 27 Mär 2023 13:56 #3

  • lazor96
  • lazor96s Avatar Autor
  • Offline
  • Fresh Boarder
  • Fresh Boarder
  • Beiträge: 8
  • Dank erhalten: 2
Hi PW,

you can do this but then you will have only 2 servos shown in the menus like butterfly or aileron differential.
So you can only set them independently in the servo settings but not in the other menus.

Best regards

Lars

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Wingtypes 27 Mär 2023 14:26 #4

  • skyfreak
  • skyfreaks Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 2946
  • Dank erhalten: 1445

Hi PW,

you can do this but then you will have only 2 servos shown in the menus like butterfly or aileron differential.
So you can only set them independently in the servo settings but not in the other menus.

Best regards

Lars


and that is where your knot is between the ears ;-)

amount of rudders set in config is what you see in differential and butterfly as S1 S2 S3 etc
and that does not equal amount of servos !!!
each rudder can be controlled by multiple servos
but in differential you want to set the difference for the rudder in total not per servo
and to get the servos in sync that react on one rudder you would use the servobalancer


JUST A REMINDER ... this is the section for jeti comments
maybe first discuss issues or problems in the adequate forum areas before posting here to get load off jeti (and I hope they read here too !!!)
Fliegergruss
GUIDO



_________________________________________________________
Too many dicks on the dance floor.
Too many dicks!​


Folgende Benutzer bedankten sich: IG-Modellbau

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von skyfreak.

Wingtypes 28 Mär 2023 10:07 #5

  • sunbeam
  • sunbeams Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 2559
  • Dank erhalten: 766
Dear Jeti-Team,

...concerning wingtypes: What about a configuration for a Delta as a predefined type?

Kind regards
Kai
Folgende Benutzer bedankten sich: stoeptegel

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Seite:
  • 1
Ladezeit der Seite: 0.213 Sekunden
Powered by Kunena Forum