Willkommen, Gast
Benutzername: Passwort: Angemeldet bleiben:

THEMA:

R5L in clone en REX12A in default 21 Jul 2021 13:28 #13

  • Nicolas
  • Nicolass Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 1091
  • Dank erhalten: 675

... It is not even possible when both recievers share the same power supply and the model has only one switch...


Hello Guido!

In this particular Setup it is possible.

Because the R5L is in a glider Dolly for steering and the Rex12 is in the glider.

Regards
Nicolas
Gruß
Nicolas
Folgende Benutzer bedankten sich: skyfreak

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

R5L in clone en REX12A in default 21 Jul 2021 14:30 #14

  • Didier
  • Didiers Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 38
  • Dank erhalten: 2
I had contact with Jeti. They have seen my video. They sayed I did the procedure correctly. They have tried it with there own equipment and it seems to work. They suggest to send everything back my TX and RX. But I fly already 2 years with my DS24 and use clone system at least in 2 jets already instead of dual path. I can’t imagine my TX is faulty.
Very annoying

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

R5L in clone en REX12A in default 21 Jul 2021 14:40 #15

  • gecko_749
  • gecko_749s Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 987
  • Dank erhalten: 294
The TX is not the problem.

Try what I told you - reset the R5 to factory default. Bind it. set it to clone. Leave the Jetibox menue menue navigating to the top level.
Switch of this RX. Bind normal RX. Switch everything off.
Start TX. Switch on both RX.
If this still doesn't work - buy another RX to replace the R5.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

R5L in clone en REX12A in default 21 Jul 2021 14:48 #16

  • gecko_749
  • gecko_749s Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 987
  • Dank erhalten: 294
I justed checked with a REX3 - if you don't leave the Menue with the up-Button the clone Mode is not stored.
Folgende Benutzer bedankten sich: skyfreak

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

R5L in clone en REX12A in default 23 Jul 2021 12:10 #17

  • Didier
  • Didiers Avatar Autor
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Beiträge: 38
  • Dank erhalten: 2
Thank you very much for all the suggestions. I really appreciate.

I did more tests today.
1, First was R5L reset to factory default, did procedure again, not working.
2, Tried another R5L to clone to a REX12Assist, not working
3, Tried one of the R5L to clone to another Assist (REX7A), not working.
4, Tried to clone a R5L to a NORMAL REX7 receiver, it worked!. Both receivers are working at the same time, ref video.
5, Tried to clone a NORMAL REX7 to a REX12ASSIST. It worked! Both receivers working at the same time, ref video.

My conclusion is. It is NOT possible to clone a R5L (probably any R receivers) to a ASSIST receiver and working at the same time. Switch off the assist RX while the R5L (clone) is on, the clone takes over.
You can clone a R5L (or any "Old" R receivers) to a NORMAL REX though.
You can clone a NORMAL REX receiver to a REX Assist receiver.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

R5L in clone en REX12A in default 23 Jul 2021 12:36 #18

  • gecko_749
  • gecko_749s Avatar
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Beiträge: 987
  • Dank erhalten: 294
Hi,

you are wong. I just have tested it with a REX10A and a R6. Works as expected.

Video.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Letzte Änderung: von gecko_749.
Ladezeit der Seite: 0.239 Sekunden
Powered by Kunena Forum